Setup 95xxx tablet with AutoCAD 12 for Windows 3.x

Note:  The 9500 series digitizers must have a firmware revision of "N" or greater to work with this driver set.  If the tablet does not operate properly after following these instructions, the firmware may be an older version.  Please contact Technical Support for information on verifying the revision.

A.  Change Digitizer in AutoCAD to "System Pointing Device"

    1.  Enter Windows

    2.  Enter AutoCAD for Windows

    3.  Type CONFIG at the Command Line to Configure AutoCAD

    4.  Select "Configure Digitizer"

    5.  Do you want to select a different one? [Y]

    6.  Select "Current System Pointing Device"

    7.  Select option "0" and EXIT with changes saved.

    8.  Exit AutoCAD for Windows and EXIT Windows.

B.  Reconfigure AutoCAD for the CalComp Driver

    1.  Enter Windows

    2.  Enter AutoCAD for Windows

    3.  Type CONFIG at the Command Line to Configure AutoCAD

    4.  Select "Configure Digitizer"

    5.  Do you want to select a different one? [Y]

    6.  Select "Wintab Compatible Digitizer by CalComp"

    7.  Answer the following questions:

        a.  Do you want to configure your digitizer as a mole?  [Y]
        b.  Do you want an audible mole/context state indicator? [Y/N]

        c.  Do you want an visible mole/context state indicator? [Y/N]

        d.  Do you want to assign a CURSOR BUTTON to toggle modes? [N]

        e.  Do you want a PRIMARY MOLE area? [Y]
         
        f.  "Enter Lower-left Hand corner now." (Defining the lower left corner of the active mole area. Select just inside the
            lower left hand corner of the active screen pointing area.)

        g.  "Enter Upper-right hand corner now." (Define the upper right corner of the active mole area. Select  just inside
             the upper right hand corner of the screen pointing area. )
     
          NOTE: The lower-left and upper-right corners that you pick for the MOLE area should define a square area just
          inside the drawing area of your template.

        h. Do you want a SECONDARY MOLE area? [N]

        i. Do you want a PRIMARY TOGGLE area? [N]

        j. Do you want a SECONDARY TOGGLE area? [N]

    8.  Type "0" to Exit to the drawing editor.

    9.  Keep configuration changes.  [Y]

   10.  Select "Preferences" under the "File" menu.

   11.  Select "Digitizer/Mouse Arbitrate" under the Digitizer Input section.

   12.  Select "Save to ACAD.INI" under AutoCAD Settings.

   13.  Select [OK]

   14.  Begin Using AutoCAD for Windows     

F.  Configuring the AutoCAD Template (ACAD.MNU only)

    1.  Type "TABLET" [ENTER] at the command line.

    2.  Type "CFG" [ENTER]

    3.  Enter the number of menu areas.

    4.  Select "4" [ENTER]

    5.  AutoCAD will now ask you to select the, Upper Left, Lower Left, and Lower Right corners of Menu Area 1 located
         at the top of your AutoCAD template.

    6.  Enter the number of columns for menu area 1:

    7.  Type "25" [Enter]

    8.  Enter the number of rows for menu area 1:

    9.  Type "9" [Enter]

   10.  Repeat steps 5-10 for menu areas 2, 3 and 4 using the columns and rows from the following table:

        a.  MENU AREA      COLUMNS     ROWS

               1                           25                9
               2                           11                9
               3                           9                13
               4                           25                7 

   11.  Do you want to respecify the Fixed Screen pointing area?  [Y]

        a.  "Digitize lower left corner of Screen Pointing Area." (Defining the lower left corner of the active mole area.
             Select the lower left hand corner of the active screen pointing area located on the template.)

        B.  "Digitize upper right corner of Screen Pointing Area." (Defining the upper right corner of the active mole area.
             Select the upper right hand corner of the active screen pointing area located on the template.)

   12.  The tablet is now configured for the AutoCAD template.